A s s e m b l y
G u i d e
X6600HRT/DA
DUAL-ACTION ELLIPTICAL TRAINER
TOOLS & PARTS INCLUDED
MM
5 Allen Wrench
Screwdriver
MM
6 L-Shaped Wrench
PARTS BOX
Heart Rate Chest Strap, Qty: 1
Power Supply, Qty: 1
Arm Bracket Covers, Qty: 2
Logo Endcaps, Qty: 2
Stabilizers, Qty: 2
Stabilizer Covers, Qty: 2
Water Bottle and Holder, Qty: 1
Console Mast Cover Plate, Qty: 1
Assembly Guide
Owner’s Guide
Warranty Card
Parts Bags
Tools
HARDWARE INCLUDED
ORANGE BAG
PINK BAG
MM
M4 x 12 Screw
MM
M8 x 12 Bolt
Quantity: 4
Quantity: 2
M8 Arc Washer
Quantity: 4
BLUE BAG
M30 Teflon Washer
Quantity: 2
MM
M4 x 12 Screw
Quantity: 4
M20 Spring Washer
Quantity: 2
MM
M3 x 10 Screw
Quantity: 1
M30 Washer
Quantity: 2
MM
M8 x 75 Bolt
Quantity: 2
STEP
1
ORANGE BAG
•
Install the left and right
stabilizers with the four arc-shaped
washers (M8) and four bolts (M8 x
STEP
1
MM
20), using the Blue 5 Allen wrench.
• Cover both stabilizers with the
included rubber boots.
STEP
2
BLUE BAG
• Slide the console mast cover onto
the console mast.
STEP
2
• Unfold the console cable and
attach it to the string located inside the
console mast. Guide the wire up
through the mast while simultaneously
sliding the console mast onto the
frame bracket.
• Attach the console mast cover to the
frame using four screws (M4 x 12).
• Bolt the mast to the frame with the
two bolts (M8 x 75), using the
MM
5 Blue-handled Allen wrench. Make
sure these are tight!
• Attach the console mast cover plate
with the V-head screw (M3 x 10).
5
STEP
3
PINK BAG
• Slide a small spring washer
(M20) onto the lower pedal arm
support, followed by the right lower
arm. Attach with a white Teflon
washer (M30), a flat washer (M30),
and bolt (M8 x 12), using Blue-han-
MM
dled 5 Allen wrench.
• Pivot the lower arm and insert the
top end into the upper handlebar
bracket.
• Tighten the bottom bolt (M8) on the
arm bracket connection block, using
the 6mm L-shaped Allen wrench.
• Repeat the above steps to attach the
arms on the left side.
STEP
3
6
STEP
4
GREEN BAG
• Slide right upper arm into right
upper handlebar bracket.
STEP
4
• Tighten the top bolt (M8) on the arm
bracket connection block, using the
MM
6 L-shaped Allen wrench.
• Attach plastic arm bracket cover to
the front of the arm bracket connection
block. This is a snap fit.
• Attach the plastic logo endcap to
the side of the arm bracket connection
block. This is a snap fit.
• Repeat the above steps on the left
side.
• Attach water bottle bracket with the
included screws.
7
STEP
5
CONSOLE
• Remove the four screws from the
back of the console. Plug the wire
connectors from inside the mast
into the console. The cable connectors
are slotted, so do not force the
connection.
STEP
5
• Mount the console to the mast using
the four screws. Do not pinch the
cable!
621-D East Lake Street
•
P.O. Box 280
•
Lake Mills. WI 53551
fax 1.920.648.3373
toll free 1.800.335.4348
•
phone 1.920.648.4090
•
2001 Vision Fitness. All Rights Reserved. 3.01 Part #Z66EP09-AG1803PRD
AG18.03PRD
REV1
8
|
Tiger Games 9 009 03 User Manual
Toastmaster Kitchen Grill TSM2032T User Manual
Toshiba DVD Player SD 3980SU User Manual
Toshiba Security Camera 625012200G User Manual
Traulsen Refrigerator RHT132NUT FHS User Manual
Tyco Electronics Computer Monitor B1ET 1215L User Manual
Ultra electronic Printer Latin Series User Manual
Venturer Digital Photo Frame DPF562SE User Manual
VTech Cordless Telephone CS6919 User Manual
Weber Gas Grill 42390 User Manual