Toto Plumbing Product MS874114S User Manual

TROUBLE SHOOTING GUIDE  
WATER LEVEL ADJUSTMENT  
1. PROBLEM: Fill valve turns on/ off without toilet being flushed  
1. To adjust, simply turn upper half of valve counter-clockwise  
INSTALLATION INSTRUCTIONS  
a. PROBABLE CAUSE: No proper slack in flapper chain to unlock, pull up til water level is where the water line is marked on  
SOLUTION: Adjust for proper slack  
b. PROBABLE CAUSE: Flush valve flapper dirty  
SOLUTION: Inspect and clean  
the overflow pipe, Fig. C, then turn clockwise till valve  
snaps into locked position.  
2. Turn on  
For MS904114 / MS884114 / MS874114S / MS914114  
water supply  
to fill tank.  
3. Tamper  
proof key is  
2. PROBLEM: Fill valve continues running  
a. PROBABLE CAUSE: Dirty fill valve seal  
SOLUTION: Shut off water supply. Open fill valve  
cap and clean valve seal  
1
4
IMPORTANT  
optional, and may be used  
simply to prevent further  
adjustment once final setting  
is achieved, Fig. D.  
b. PROBABLE CAUSE: Flush valve flapper does not  
seat properly  
Read these instruc-  
tions thoroughly  
before beginning  
work.  
SOLUTION : Inspect, clean or adjust flapper position  
c
a
b
3. PROBLEM: Poor Flush  
a. PROBABLE CAUSE: Trapway is obstructed  
SOLUTION: Unclog trapway  
b. PROBABLE CAUSE: Supply stop is partially closed  
SOLUTION: Open supply stop  
c. PROBABLE CAUSE: Venting is obstructed  
SOLUTION: Clear venting pipe  
d. PROBABLE CAUSE: Water supply is too low  
SOLUTION: The minimum required supply pressure  
is 20 psi. Consult your plumber.  
d
You have purchased  
one of the best  
working toilets  
available today,  
backed by TOTOs  
worldwide finest  
reputation.  
2
SERVICING  
INSTRUCTIONS  
3
1. Turn off water supply, then  
flush toilet.  
f
5
TSU01W  
2
3
2. Snap off cover.  
Please leave instructions for customers. These instructions  
contain maintenance and warranty information.  
3. Gently press float arms inward and  
remove float.  
4. PROBLEM: No flushing  
e
a. PROBABLE CAUSE: Supply stop is closed  
SOLUTION: Open supply stop  
b. PROBABLE CAUSE: Flush valve chain is too loose  
or disconnected  
COMMON TOOLS NEEDED:  
12pipe wrench  
10adjustable wrench  
Carpenters level  
Tape measure  
Plier  
4. While holding valve with one hand,  
twist cap 1/ 8 turn counter clock-  
wise and remove.  
Model  
A
B
C
D
SOLUTION: Adjust chain length as needed  
MS904114  
MS884114  
29-1/ 215”  
23-1/ 221-1/ 4”  
23-3/ 416-1/ 2”  
27-1/ 216-1/ 2”  
24-7/ 817-3/ 4”  
5. Lift out center tube as shown.  
WARNING! DO NOT USE IN-TANK BOWL CLEANERS  
28”  
28”  
28”  
15”  
15”  
15”  
Screwdriver  
Putty knife  
The use of high concentration of chlorine or chlorine-related products can  
seriously damage fittings in the tank. This damage can cause leakage and  
property damage. • TOTO shall not be responsible or liable for any tank fit-  
ting failure or damage caused by the use of in-tank bowl cleaners.  
6. Remove strainer form center tube  
as shown. Clean strainer and cap  
by rinsing off under faucet.  
MS874114S(SG)  
Drill motor, 11/ 64drill bit (for wood floor  
installation) & 1/ 4masonry drill bit (for masonry/ tile  
floor installation)  
MS914114  
7. Carefully reassemble the valve in  
the reverse order.  
* Check for correct dimension  
TOILET TANK FILL VALVE INSTRUCTIONS  
G-Max /Power Gravity  
MATERIALS REQUIRED:  
Supply tube / connector  
Supply stop  
Mounting bolts (2)  
Wax ring / seal  
4
5
IMPORTANT:  
INSTALLATION  
1. Shut off water supply. Flush toilet;  
sponge remaining water from tank.  
Remove old ballcock.  
2. Slide threaded valve-shaft through hole in  
bottom of tank. Note:  
Note position of cap when properly  
assembled to the body. The ribs on  
the cap are in line with the float  
chamber and the refill port is aligned  
as shown.  
A
D
3/4"  
Package Content:  
No. Item  
Quantity  
Be sure to install  
valve in the locked  
position at the angle  
shown in fig. A.  
Thread mounting-  
nut onto exposed  
1.  
2.  
3.  
4.  
5.  
Vitreous China Bowl w/ lid ..............................................1  
Cover Plate ..............................................................................2  
Top Mount Bolt Set (for seat) ........................................1  
Toilet Seat Set ........................................................................1  
UNIFIT Rough-In (TSU01W.12) .................................1  
5a. Toilet Mounting Bolt (T-Bolt) ...............................2  
5b. T-Bolt Washer................................................................2  
5c. T-Bolt Nut.......................................................................2  
5d. Mounting Screw w/ washer....................................4  
5e. Anchor ..............................................................................4  
5f. PVC Outlet Connection*..........................................1  
C
B
4-1/2" *  
shaft under tank and tighten nut.  
DO NOT OVERTIGHTEN.  
3. Connect water supply as shown in fig. B.  
Pipe dope is not recommended. Hand tight-  
en only; do not overtighten coupling nut.  
4. Finally attach refill tube to valve and clip  
other end to overflow pipe.  
10"  
12"  
14"  
8" *  
(Only for MS904114)  
10" *  
6
7
TOTO U.S.A., INC. • 1155 Southern Road, Morrow, GA 30260  
Tel. (770) 282-8686 • Fax. (770) 282-8701  
NOTE: Water supply rough-in  
significantly wider than standard 5"rough-in.  
Consult your builder or contractor.  
Printed in U.S.A. © TOTO LTD.  
REV 03/01  
 
OGU003Z  

Texas Instruments Stereo Amplifier TAS5508 5142K7EVM User Manual
Toshiba Satellite TV System 1805 User Manual
Trane Air Conditioner RT PRC010 EN User Manual
Triarch Indoor Furnishings 60165 User Manual
Triarch Indoor Furnishings 75366 10 User Manual
Tripp Lite Battery Charger BP12V81 User Manual
Tripp Lite TV Cables B015 000 User Manual
Uniden Telephone DECT1588 User Manual
VeriFone IP Phone Omni 37xx User Manual
Vermont Casting Outdoor Fireplace BC36 User Manual